P0060
Fix within 1-2 weeksOxygen Sensor Heater Circuit Resistance (Bank 2 Sensor 2)
Code P0060 means your Bank 2 Sensor 2 oxygen sensor heater circuit has incorrect resistance. Common causes: Faulty O2 sensor (85%), wiring issues (10%), blown fuse (4%). Drivability: Yes, safe to drive. Repair cost: $50-$200 DIY, $150-$500 professional.
Can I Drive With P0060?
Yes, safe to drive
No restrictions
Stop driving immediately if: Flashing Check Engine Light, loud exhaust noises, burning smell, significant power loss.
Symptoms of P0060
- 1Check Engine Light is on
- 2Reduced fuel economy
- 3Increased exhaust emissions
- 4Engine may run rough at startup (less common)
Common Causes of P0060
Parts most likely causing this code, ranked by probability
The heater element inside the oxygen sensor has failed, causing incorrect resistance readings.
85% of P0060 cases are fixed by replacing this part
Damaged, corroded, or loose wiring or connector pins for the Bank 2 Sensor 2 heater circuit prevent proper operation.
10% of P0060 cases are fixed by repairing this part
A fuse protecting the oxygen sensor heater circuit has blown, cutting power to the heater.
4% of P0060 cases are fixed by replacing this part
An internal fault in the PCM affects the oxygen sensor heater circuit control.
1% of P0060 cases are fixed by replacing this part
Check These First (Before Buying Parts)
- Visually inspect the Bank 2 Sensor 2 and its wiring for any obvious damage, fraying, or corrosion.
- Check the fuse box for any blown fuses related to the oxygen sensor heater circuit.
How to Diagnose P0060
- 1Visually inspect the Bank 2 Sensor 2 and its wiring harness for any signs of damage, corrosion, or loose connections.
- 2Locate the fuse for the oxygen sensor heater circuit (check your vehicle's service manual) and inspect it for continuity.
- 3Disconnect the Bank 2 Sensor 2 electrical connector and use a multimeter to measure the resistance across the two heater wires (usually the same color, often white). Compare to factory specifications.
- 4With the key on, engine off, use a multimeter to check for 12V power and a good ground at the oxygen sensor harness connector (for the heater circuit).
- 5If the sensor resistance is out of specification, replace the oxygen sensor. If wiring/power/ground are faulty, repair as needed.
P0060 on Popular Vehicles
Toyota Camry
2007-2024P0060 on these models is frequently resolved by replacing the Bank 2 Sensor 2 oxygen sensor. The sensor heater element is a common failure point.
85% fixed by Oxygen Sensor (Bank 2 Sensor 2)
Honda Accord
2003-2024For Honda Accords, P0060 often points directly to a faulty Bank 2 Sensor 2 oxygen sensor. Wiring issues are less common but should still be checked.
85% fixed by Oxygen Sensor (Bank 2 Sensor 2)
Ford F-150
2004-2024P0060 on F-150s is a common code, with the Bank 2 Sensor 2 oxygen sensor being the primary culprit. Corrosion on the sensor connector can also contribute.
85% fixed by Oxygen Sensor (Bank 2 Sensor 2)
Chevrolet Silverado
2007-2024Silverado owners reporting P0060 often find the Bank 2 Sensor 2 oxygen sensor has failed. Inspecting the harness for rodent damage is also a good idea.
85% fixed by Oxygen Sensor (Bank 2 Sensor 2)
Frequently Asked Questions
What does P0060 mean?
P0060 indicates an issue with the heater circuit resistance for the Bank 2 Sensor 2 oxygen sensor. This sensor is located after the catalytic converter on the engine bank that does not contain cylinder #1.
Can I drive with P0060?
Yes, safe to drive. Your vehicle will likely experience reduced fuel economy and increased emissions, but it will not cause immediate damage to the engine.
Will P0060 clear itself?
No, P0060 will not clear itself. The Powertrain Control Module (PCM) requires the heater circuit resistance to be within specification for a certain number of drive cycles before the code will clear. You will need to diagnose and fix the underlying issue.
How do I fix P0060 myself?
Start by visually inspecting the sensor and wiring. Check the fuse for the O2 sensor heater. Then, test the resistance of the Bank 2 Sensor 2 heater element with a multimeter. If the resistance is out of specification, replace the oxygen sensor.
How much does it cost to fix P0060?
A DIY fix typically costs $50-$200 for a new oxygen sensor. Professional repair at a shop will cost $150-$500, including parts and labor.
P0060 keeps coming back - why?
If P0060 keeps returning, it often means the initial diagnosis was incomplete. Double-check the wiring harness for intermittent shorts or opens, ensure the replacement sensor is correct and fully seated, and verify power and ground to the heater circuit are stable.
Will P0060 fail emissions/smog test?
Yes, P0060 will cause your vehicle to fail an emissions or smog test. The Check Engine Light being on automatically results in a failure in most jurisdictions.
What's the difference between P0060 and P0059?
P0060 refers to the heater circuit resistance for Bank 2 Sensor 2. P0059 refers to the heater circuit resistance for Bank 2 Sensor 1. They indicate the same type of fault but on different oxygen sensors.
P0060 on Ford F-150?
On many Ford F-150 models, P0060 is commonly caused by a failed Bank 2 Sensor 2 oxygen sensor. These sensors can degrade over time, especially in areas exposed to road salt or moisture.
Questions to Ask Your Mechanic
Did you check the resistance of the Bank 2 Sensor 2 heater circuit with a multimeter?
Good answer: A good answer confirms the specific test was performed and provides the reading compared to specifications.
What did you find when checking power and ground to the O2 sensor heater connector?
Good answer: A good answer details the voltage and ground integrity at the connector.
Repair Cost Estimate
DIY Repair
Parts only
$50-$200
Shop Repair
Parts + labor
$150-$500
Save $100-$300 by doing it yourself
Difficulty
intermediate
Time
1-2 hours
Intermediate - requires basic hand tools, a multimeter, and an oxygen sensor socket. Access to the sensor can sometimes be challenging.
Cost of Waiting
Ignoring P0060 means your engine's computer is not getting accurate exhaust data from that sensor. This leads to reduced fuel economy and increased harmful emissions. While it won't immediately damage your engine, prolonged driving with incorrect fuel trims can eventually impact the lifespan of your catalytic converter, a repair that costs $800-$2,500.
While You're In There...
If you need to remove exhaust components to access the sensor, replacing old gaskets prevents exhaust leaks.
Applying anti-seize to the new O2 sensor threads prevents future seizing and makes removal easier.
Tools You'll Need
- OBD-II scan tool
- Multimeter
- Oxygen sensor socket (7/8" or 22mm)
- Ratchet and extensions
- Wire brush (for cleaning threads)
- Anti-seize compound
P0060 is a common emissions code. Most repairs involve replacing the oxygen sensor, which is a straightforward job that restores your vehicle's fuel efficiency and reduces emissions.
- Family-owned since 1957
- 990,000+ happy customers
- Fast nationwide shipping
- Easy returns
Your Next Steps
Step 1: Visually inspect the Bank 2 Sensor 2 and its wiring harness for any signs of damage, corrosion, or loose connections. Check the fuse for the O2 sensor heater circuit.
Step 2: If the visual inspection and fuse check don't reveal the problem, disconnect the sensor and use a multimeter to test the resistance of the heater element. Compare the reading to your vehicle's specifications.
Step 3: If the sensor's resistance is out of specification, you'll likely need a new Bank 2 Sensor 2 oxygen sensor.