P0394 Code
Fix within a few daysCamshaft Position Sensor 'B' Circuit Intermittent (Bank 2)
What Does P0394 Mean?
Code P0394 means your engine's Bank 2, Sensor B camshaft position signal is intermittent. Common causes: Camshaft position sensor (70%), wiring (20%). Drivability: Limit driving, fix within a few days. Repair cost: $50-$200 DIY, $150-$400 professional.
Can I Drive With P0394?
Limit driving, fix within a few days
Essential trips under 10 miles, avoid highways and heavy acceleration. Be prepared for potential stalling.
Stop driving immediately if: Engine stalls repeatedly, significant power loss, loud knocking noises, or a flashing Check Engine Light.
What Are the Symptoms of P0394?
- 1Engine cranks but does not start
- 2Engine stalls shortly after starting
- 3Rough idle
- 4Reduced engine power
- 5Poor fuel economy
- 6Engine misfires
- 7Check Engine Light is on
What Causes P0394?
Parts most likely causing this code, ranked by probability
The sensor itself fails internally, sending an inconsistent signal to the engine computer.
70% of P0394 cases are fixed by replacing this part
Damaged, corroded, or loose wiring or a faulty connector causes an intermittent signal interruption.
20% of P0394 cases are fixed by repairing wiring or connector
Mechanical issues with the timing chain, belt, or variable valve timing (VVT) actuator can cause the camshaft position to be intermittently incorrect, leading to an intermittent sensor signal.
8% of P0394 cases are fixed by addressing timing components
A rare internal fault within the engine computer can incorrectly interpret or process the camshaft position sensor signal.
2% of P0394 cases are fixed by replacing the ECM/PCM
Check These First (Before Buying Parts)
- Visually inspect the camshaft position sensor's electrical connector for looseness, corrosion, or bent pins.
- Check the wiring harness leading to the sensor for any signs of damage, fraying, or rodent chew marks.
- Ensure your engine oil is at the correct level and is not excessively dirty, as low or old oil can affect VVT systems.
How to Diagnose P0394
- 1Visually inspect the camshaft position sensor (Bank 2, Sensor B) and its wiring/connector for damage, corrosion, or looseness.
- 2Using a multimeter, test the sensor's resistance and voltage output according to service manual specifications.
- 3If available, use an oscilloscope to monitor the sensor's signal for intermittent drops or inconsistencies.
- 4Check for proper engine oil level and condition, as low oil can affect VVT systems.
- 5If the sensor and wiring check out, inspect the timing chain/belt for slack or wear, and check VVT actuator operation.
How Do I Fix P0394 on My Vehicle?
Ford F-150
2004-2024Ford's VCT system can be sensitive. While P0394 points to the sensor, ensure engine oil is clean and at the correct level, as VCT solenoid issues can sometimes mimic or contribute to cam sensor problems.
65% fixed by replacing Camshaft Position Sensor
Shop for Ford F-150Honda Accord
2003-2024On Honda Accords, the camshaft position sensor is a common failure point. Access can be tight on some V6 engines. Always check the wiring harness for rodent damage or corrosion.
75% fixed by replacing Camshaft Position Sensor
Shop for Honda AccordChevrolet Silverado
2007-2024Silverados with V8 engines often have the camshaft position sensor located at the rear of the engine block or near the timing cover. Wiring integrity is crucial, as heat and vibration can degrade connections over time.
70% fixed by replacing Camshaft Position Sensor
Shop for Chevrolet SilveradoFrequently Asked Questions
What does P0394 mean?
P0394 indicates that the engine computer is receiving an intermittent signal from the 'B' camshaft position sensor on Bank 2. This sensor helps the computer know the exact position of the camshaft for proper engine timing.
Can I drive with P0394?
Limit driving, fix within a few days. You can drive for short, essential trips, but expect reduced engine performance, potential stalling, and poor fuel economy. Continued driving risks further engine damage or leaving you stranded.
Will P0394 clear itself?
No, P0394 will not clear itself. The intermittent fault needs to be diagnosed and repaired. The Check Engine Light will remain on until the underlying issue is resolved and the code is cleared, either manually or after several drive cycles without the fault.
How do I fix P0394 myself?
Start by visually inspecting the Bank 2, Sensor B camshaft position sensor and its wiring for any obvious damage or loose connections. If the wiring looks good, replace the camshaft position sensor. This is often a straightforward job requiring basic hand tools.
How much does it cost to fix P0394?
A DIY repair for P0394 typically costs $50-$200 for a new camshaft position sensor. If you take it to a shop, expect to pay $150-$400, which includes the part and 1-2 hours of labor.
P0394 keeps coming back - why?
If P0394 keeps returning, the initial repair did not address the root cause. This often means the wiring or connector is still faulty, or there's a deeper mechanical issue like a stretched timing chain or a failing VVT actuator that is causing the intermittent signal.
Will P0394 fail emissions/smog test?
Yes, P0394 will cause your vehicle to fail an emissions or smog test. The Check Engine Light being on automatically results in a failure in most states, and an intermittent camshaft position sensor signal directly impacts engine timing and emissions control.
What's the difference between P0394 and P0390?
P0394 specifically indicates an intermittent circuit issue for Camshaft Position Sensor 'B' on Bank 2. P0390 is a more general code indicating a circuit malfunction for Camshaft Position Sensor 'B' on Bank 2, which could be a constant open, short, or incorrect signal, not necessarily intermittent.
P0394 on Ford F-150
On Ford F-150s, especially those with VCT (Variable Cam Timing) systems, P0394 often points directly to a failing camshaft position sensor on Bank 2. However, it's important to also check the VCT solenoids and oil passages, as issues there can sometimes indirectly affect cam sensor readings.
Questions to Ask Your Mechanic
Did you test the signal from the Bank 2, Sensor B camshaft position sensor with an oscilloscope to confirm the intermittent fault?
Good answer: Yes, we saw intermittent signal drops on the oscilloscope, confirming the sensor or its circuit is failing intermittently.
Have you checked the wiring harness and connector for corrosion or damage leading to the camshaft position sensor?
Good answer: Yes, we thoroughly inspected the wiring and connector for any signs of damage, fraying, or corrosion, and they appear to be in good condition.
Repair Cost Estimate
DIY Repair
Parts only
$50-$200
Shop Repair
Parts + labor
$150-$400
Save $100-$200 by doing it yourself
Difficulty
intermediate
Time
1-2 hours
Intermediate. Replacing the sensor itself is often straightforward, but diagnosing intermittent wiring issues or deeper mechanical problems requires more advanced tools and knowledge.
Cost of Waiting
Ignoring P0394 can lead to severe drivability issues like stalling and misfires. Continued misfires send unburned fuel to your catalytic converter, which can destroy it. A $50-$200 sensor job now prevents a $1,200-$2,500 catalytic converter replacement later.
While You're In There...
If the camshaft position sensor is located under the valve cover, replacing the gasket prevents oil leaks and is often necessary when accessing the sensor.
Clean engine oil is critical for proper VVT system operation. If you suspect VVT issues, fresh oil and a new filter are a good preventative measure.
Tools You'll Need
- Basic socket set
- Wrench set
- Multimeter
- Screwdriver set
- Wire brush (for cleaning connectors)
Related Codes
The engine computer isn't getting a proper signal from the camshaft position sensor on Bank 1.
The engine computer is receiving an inconsistent or incorrect signal from the camshaft position sensor 'A' on Bank 1.
Your engine computer isn't getting a proper signal from the camshaft position sensor on Bank 2. Bank 2 is the side of your engine that does not contain cylinder #1.
The engine computer is not receiving the correct signal from the camshaft position sensor on Bank 2, which is critical for engine timing.
The engine computer isn't getting a proper signal from the Bank 2, Sensor B camshaft position sensor.
Your engine's computer isn't getting the right signal from the Camshaft Position Sensor 'B' on Bank 2. This sensor tells the computer where the camshaft is, which is critical for engine timing.
Camshaft Position Sensor 'B' Circuit Low (Bank 2)
Camshaft Position Sensor 'B' Circuit High (Bank 2)
P0394 is a common sensor issue. Most repairs are under $200 and your engine will run smoothly and reliably afterward.
- Family-owned since 1957
- 990,000+ happy customers
- Fast nationwide shipping
- Easy returns
Your Next Steps
Step 1: Perform a thorough visual inspection of the Bank 2, Sensor B camshaft position sensor and its wiring/connector. Look for any obvious damage, corrosion, or loose connections.
Step 2: If the visual inspection reveals no issues, test the sensor's resistance and voltage output with a multimeter. Compare readings to your vehicle's service manual specifications. If the sensor tests bad or shows intermittent readings, replace it.
Step 3: If the sensor and wiring appear good, consider professional diagnosis to check for timing chain slack or VVT actuator issues. Parts you'll likely need: a new camshaft position sensor.
